Proface FP3900 - 19 Flat Panel" Uživatelský manuál stáhnout pdf

FP-3900T Series

Installation Guide

Package Contents

 FP unit (1)

 Installation Guide (1) (this manual)

 Warning/Caution Information (1)

 Installation Gasket (1) (attached to the FP

unit)

 Installation Fasteners (4/set, 3sets)

 USB Cable Clamp (1)

AC Power Connector (1) (attached to the

FP unit)

This unit has been carefully packed, with

special attention to quality. However, should

you find anything damaged or missing, please

contact your local FP distributor immediately.

Required software/Reference

manual

The FP-3900T unit needs the following

software for operation. As FP user manual,

provided by PDF media, describes its details,

download the manual below and get the further

information. Visit Pro-face website below and

get both software and reference manual.

(URL:http://www.pro-face.com/otasuke/)

• Software : Mouse Emulation Software

• Manual : FP3000 Series User Manual

• Before you begin to use the touch

panel, you need to adjust (calibrate) it.

• For use of USB for sending touch data,

the number of the calibration point of

mouse emulation software should be

9. (The initial setting is 4.)

If you do not change the setting values,

the touch position may not be accu-

rate, a little off the point.

• If the touch panel coordinates slip, it is

recommended to make calibration

again.

UL/c-UL/CSA Application

Notes

Be aware of the following items when

building the FP into an end-use product:

• The rear face of the FP unit is not a part of

an enclosure. This unit must be used as a

built-in component of an end-use product

that forms a UL/c-UL-compliant enclosure.

• For indoor use only.

• This unit should be installed in the front

face of a metal panel.

• If this unit is installed so as to cool itself

naturally, be sure to install it in a vertical

panel. Also, be sure that the FP unit is

mounted at least 100 mm away from any

adjacent structures or equipment. If these

requirements are not met, the heat gener-

ated by the FP unit’s internal components

may cause the unit to fail to meet UL/c-UL

standard.

• For u

se on a flat surface of a Type 4X

(Indoor Use Only) and/or Type 12 Enclo-

sure.

•

Type 4X (Indoor Use Only) and/or 12

Enclosure, when the hatch for Front USB

Port is secured by screw.

Type 1 Enclosure, when the hatch for Front

USB

Port is open.(FP3900-T41-U only)

Caution

Be sure to read the “Warning/Caution

Information” on the attached sheet before

using the product.

1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - Installation Guide

1FP-3900T Series Installation GuidePackage Contents FP unit (1)  Installation Guide (1) (this manual) Warning/Caution Information (1) Installation

Strany 2 - CE Marking Notes

10Wiring• To avoid an electric shock, when connecting the FP’s power cord terminals to the power ter-minal block, confirm that the FP’s power supply i

Strany 3 - Part Names

11*1 If the Conductor’s end (individual) wires are not twisted correctly, the end wires may either short against each other, or against an electrode.

Strany 4 - Dip Switches and Slide Switch

12 USB Cable Clamp Removal Fea-ture(1) Push in the cable clamp’s stopper until the cable clamp is unlocked, then remove the clamp.(2) Disconnect the

Strany 5 - Interfaces

13Starting the OSDTo start the OSD and enter OSD mode, press the three corners of the touch panel in turn (upper left, upper right, and lower right) w

Strany 6 -  DVI-D Interface

14Top Main• In the OSD, pressing the button applies the set value and enables the setting. The set value won’t be canceled unless the powe

Strany 7 -  Serial Interface

15 720x400 ModeWhen an input data resolution of 720 x 400 is used in the VGA text mode, set this parameter to ON. For other resolutions, set this pa

Strany 8

16NoteRegardless of the above clause, Digital Electronics Corporation shall not be held responsible for any damages or third-party claims for damages

Strany 9 - Installation

2• Receivable signals are only from isolated secondary source.•All interface ports (except for Front USB Connector (Type A) ) are not intended to be d

Strany 10 -  Power Cord Specifications

3Part Names CDEFGHFront ViewRear ViewBottom ViewA,BJIA: TFT Color LCDActs as a display monitor for your host.B: Touch PanelAllows you to switch scre

Strany 11 - Using the USB Cable Clamp

4Dimensions Dip Switches and Slide SwitchThe Dip Switches and Slide Switch are located in the bottom of the FP unit. Loosen the screws of the cover

Strany 12 - OSD Functions

5Interfaces Analog RGB InterfaceThe number of dots (pixels) displayed are as follows: Pin Assignments and Signal Names for Analog RGBInput signal t

Strany 13 - Using the OSD

6Connector...Mini Dsub 15 pin maleConnector set screw ...#4-40 UNCCable...RGB cable manu

Strany 14 - Top Main

7Pin Assignments and Signal Names for DVI-D Connector...DVI-D 24-pin maleConnector set screw ...#4-40 UNCCable...

Strany 15

8Pin Assignments and Signal Names for Serial InterfaceConnector...Dsub 9 pin femaleConnector set screw ...#4-40 UNCCabl

Strany 16

9Installation(1) According to the Panel Cut size, make installation holes on the panel. Also, determine the panel thickness according to the panel thi